【转帖】【原创】IBM thinkpad X60T fn 和 ctrl 按键 刷 BIOS 换位

guohanchen21

IBM THINKPAD 的fn和ctrl按键实位置不是很适合我。所以琢磨着换一下这两个按键的位置。因此找到了国外的一片文章，里面有一些thinkpad型号笔记本的修改BIOS内容。通过刷新bios可以实现fn键和ctrl按键的换位。
http://forum.notebookreview.com/ ... laptops-solved.html



型号列表如下
upported models:
Lenovo G430, G530
Lenovo G450, G550
Lenovo G455, G555
Lenovo N200 (type 0769)
Lenovo N500, G530 (MT 4446 only)
IdeaPad S9, S10
IdeaPad S9e, S10e, S10 with 3G (MT 4329, 4333)
IdeaPad S10-2
IdeaPad S10-3
IdeaPad S10-3t
IdeaPad U350
IdeaPad U450, U450p
IdeaPad Y430
IdeaPad Y450
IdeaPad Y530
IdeaPad Y550
IdeaPad Y550p
IdeaPad Y460, Y560
IdeaPad Y460p, Y560p

ThinkPad SL300, SL400, SL400c, SL500, SL500c
ThinkPad L410, L510, SL410, SL510
ThinkPad R400, T400
ThinkPad R500
ThinkPad R60, R60i (Machine types 94xx)
ThinkPad R61
ThinkPad T400s
ThinkPad T500, W500
ThinkPad T60, T60p
ThinkPad T61, T61p
ThinkPad W700, W700ds
ThinkPad X200, X200s
ThinkPad X200 Tablet
ThinkPad X300
ThinkPad X301
ThinkPad X60, X60s
ThinkPad X60 Tablet
ThinkPad X61, X61s
ThinkPad X61 Tablet


Attention to ThinkPad owners.
If you get error message during BIOS update:
"BIOS image file is same as BIOS ROM. An update is not necessary at this time."
OR
you flashed the patch but FN and CTRL are still not swapped
then you have to do the following:

1) Create "flash.bat" file in the folder with WINUPTP.EXE. Bat-file should have the following contents:

@echo off
echo Updating BIOS. Please wait...
winuptp.exe /s
echo BIOS flash completed. Reboot your machine now.
pause

2) Run flash.bat as administrator, you'll see "Updating BIOS. Please wait..." message.

3) Wait until "BIOS flash completed. Reboot your machine now." message is displayed.

4) Reboot your machine.

flash.bat is attached just in case.


If you want to bring back (for some reason) the original FN-CTRL layout, then follow the instructions below:

- For all non-ThinkPad models: just flash the original BIOS.

- ThinkPad owners have to do the following:

1) Download the latest BIOS update utility for Windows from the official website.

2) Run it and remember the folder where the update utility will be installed.

3) Uncheck "Install ThinkPad BIOS Update Utility now" on the last screen of the setup wizard and click "Finish".

4) Go to the folder where the update utility was installed, and then place flash.bat there.

5) Run flash.bat as administrator, you'll see "Updating BIOS. Please wait..." message.

6) Wait until "BIOS flash completed. Reboot your machine now." message is displayed.

7) Reboot your machine.

If flash.bat quits instantly, then something goes wrong. Read Winuptp.log (it will be created in the same folder with flash.bat) to determine the cause of the issue.
Run flash.bat again after eliminating all the causes.
翻译如下：
注意ThinkPad的主人。
如果你得到错误消息在BIOS更新:
“BIOS镜像文件是更新BIOS芯片一样。没有必要。”
或
你闪过补丁但FN和CTRL仍不交换

然后你必须做到以下几点:

1)创建“闪电。蝙蝠与WINUPTP.EXE“文件的文件夹。bat文件应该有以下内容:

[url=]@echo[/url]从
回声更新BIOS。请稍等…
winuptp。exe /秒
回声BIOS闪存完成。现在可以重启你的电脑。
暂停

2)运行flash。蝙蝠是管理员,您将会看到“更新BIOS。请稍等…”消息。

3)等到“BIOS闪存完成。现在可以重启你的电脑。”信息出现。

4)重新启动您的计算机。

闪光。蝙蝠是以防。


如果你想恢复原始FN-CTRL布局(由于某种原因),然后遵循下面的说明:

——所有non-ThinkPad模型:flash最初的BIOS。

——ThinkPad所有者必须做到以下几点:

1)下载最新的BIOS更新实用程序从官方网站为Windows。

2)运行它,记住更新实用程序将安装的文件夹中。

3)取消“现在安装ThinkPad BIOS更新实用程序”设置向导的最后一个屏幕上,单击“完成”。

4)去安装更新实用程序所在的文件夹,然后闪光的地方。蝙蝠。

5)运行flash。蝙蝠是管理员,您将会看到“更新BIOS。请稍等…”消息。

6)等到“BIOS闪存完成。现在可以重启你的电脑。”信息出现。

7)重新启动您的计算机。

如果flash。蝙蝠立即退出,然后出现问题。读Winuptp。[backcolor=rgb(240, 240, 160) !important]日志(它将在同一个文件夹中创建flash.bat)来确定问题的原因。
运行flash。蝙蝠后再取消所有的原因。



物理上的按键互换：
扣下来fn和ctrl按键，调换位置，就可以实现了。

guohanchen21

forum.notebookreview.com/threads/fn-ctrl-swap-on-all-lenovo-laptops-solved.474396/

屋檐上的猫

这也行?楼主真牛.