|
|
发表于 2003-11-6 20:54:18| 字数 7,570| - 中国–北京–北京 鹏博士BGP
|
显示全部楼层
thinkker
目前网上大部分提供下载的SOFTFSB不支持SG577,需要下载V1.7FINAL版.
下载:http://www.dark-tweaker.com/downloads-system.htm
SoftFSB
Version 1.7x
English documentation
About SoftFSB
Warning !!
Supported Operating Systems
Operations
Supported PLL-ICs
Unsupported PLL-ICs
Special thanks
History
Reproducing/Distributing/Copying
Copyright
Contact me
About SoftFSB
The purpose of this Windows application is to change the base clock ( FSB / Front Side Bus ) frequency without having to restart the machine. Any FSB changes are instantaneous.
Originally this software was made to see if it was possible to set FSB values which cannot be set by using the BIOS.
Warning !!
If you are a beginner, do not use this software. This software is for power users only.
If you don't know who manufactured your motherboard, or your PLL-IC model, do not use this software.
Use "SoftFSB.EXE" at your own risk.
You should change the FSB up and down one step at a time because you may damage the CPU if you don't.
(For example, if you change it from 66MHz to 133MHz in one go ... that's bad news!)
If you raise the FSB too high then it is possible that the CPU may not function correctly anymore, and the system will hang.
If your PC hangs and you can't restart it, power off. Wait a little while and turn it on again, after making sure that no damage has been done to any of your PC components. Also, if it does not return to how it was normally, you must clear your CMOS
"Does SoftFSB support my M/B or PC ?" I hear you ask; the answer is "I don't know !!".
Don't send me e-mails regarding this question.
Visually check the PLL-IC type on your motherboard. If the PLL-IC that you found is listed in SoftFSB then try it!
If you ask me "Does SoftFSB support my PLL-IC ?", don't forget to include the following information:
Motherboard name (Eg: ASUS P2B Revision 1.10 )
Chip-set name (Eg: BX Chip-set )
PLL-IC name (Eg: Winbond W83194R-39A )
The URL where I can find the data sheet of your PLL-IC.
It is possible to make the PLL-IC data file with yourself, even if in SoftFSB this is an unsupported PLL-IC. Please try to make the PLL-IC data file yourself and see the datasheet of PLL-IC first of all.
Supported Operating Systems
SoftFSB runs under Windows 95/98 and Windows NT 4.0/5.0 in both Japanese and English language versions
It will probably run with the following chipsets ...
Intel PIIX4, PIIX4E Controller M/B
440BX, 440ZX, 440EX, 440GX, 440LX, 430TX, 450NX Chipset
Intel 82801AA, 82801AB Controller M/B
i810, i810e, i820, i840 Chipset
VIA VT82C596A, VT82C596B, VT82C586B, VT82C686A Controller M/B
Apollo Pro 133/133A, Apollo Pro Plus, Apollo Pro, Apollo MVP3, Apollo VP3 Chipset
AMD 756 Controller M/B
AMD-750 Chipset
SoftFSB will run on any motherboards referred to on my Official HomePage.
* The PLL-IC chipset used may differ with differents revisions of the motherboard. If it won't run with your revision, chipset etc, sorry :-)
* The AOpen motherboards are different and can not retrieve information on the current FSB.
If you are using the M/B (temperature) sensor software, maybe ... you can't use SoftFSB.
Mr. t_knz "MAX1617 monitor software 1617mon" and Mr.PENTIUM 666MHz "LM75/LM78 STATUS for Windows WLMSTAT" are already supporting a synchronous control. You can use it at the same time as SoftFSB.
If you are using WaterFall Pro ... You can use SmartBus Control Module. and add SoftFSB.ini, but "this operation is unguaranteed"
[EXTOPTION]
SmartBus=1
Operations
Choosing a Motherboard from the Motherboard Menu
Choose your Motherboard from "Target Motherboard".
Click the "Get FSB" button.
"Current FSB (PCI) : External", the "Select FSB (PCI) : External" menu, "Set FSB", the "TaskTray" button, and the "Slide bar" for selecting the FSB(PCI) are enabled.
Set the FSB(PCI) using the "Slide bar".
Click on the "Set FSB" button.
If that operation completes correctly, the FSB clock will change.
Choosing a PLL-IC from the PLL-IC Menu
Choose your PLL-IC from "Target Clock Generator (PLL-IC)".
Click the "Get FSB" button.
"Current FSB (PCI) : External", the "Select FSB (PCI) : External" menu, the "Set FSB" button, and the "Slide bar" for selecting the FSB(PCI) are enabled.
Set the FSB(PCI) using the "Slide bar".
Click on the "Set FSB" button.
If that operation completes correctly, the FSB clock will change.
Using the TaskTray mode
Perform one of the above two steps.
Click on the "Get FSB" button, and the "TaskTray" button will be enabled.
Click on the "TaskTray" button.
Turn "Enable TaskTray" ON.
Select the "Auto Start" tab. Select the FSB(PCI) Value to be set when SoftFPS starts up.
and turn "Enable setting" ON.
Select the "Auto Exit" tab. Select the FSB(PCI) Value to be set when SoftFPS quits.
and turn "Enable setting" ON.
After you restart SoftFSB, the TaskTray mode will be enabled.
If you want the same FSB setting every time you reboot, added SoftFPS to the Startup folder in the Start Menu.
Making/adding a PLL-IC data file with yourself
Select the menu "File" - "Create" - "PLL-IC Data ...". open "SoftFSB PLL-IC data creator" window.
Seeing the datasheet of PLL-IC. and Input of all items in the window (use this picture for reference)
Saving the file (*.PLL).
Active the "Target Clock Generator".
Select the menu "Import PLL-IC ...". and load a PLL-IC data file.
It can select new PLL-IC with "Target Clock Generator".
*If you put/save the new PLL-IC to the same folder with SoftFSB, It is possible to load automatically at the time of SoftFSB starting.
Supported PLL-ICs
At present the following PLL-ICs have been tested with SoftFSB.... However, there is no guarantee that any of these will work with your motherboard.
IC-Works
W123x W124x W126x W127x
W131x
W144x W145x W148x W149x
W150x W153x W156x
W160x W164x
W196x
W204x
W42S51-01x
W48S68-01x W48S68-03x
W48S87-04x W48S87-27x
W48S88-01x W48S88-03x
W48S101-04x W48S111-14x W48S112-24x
ICS
9148xx-04 9148xx-08 9148xx-17 9148xx-26 9148xx-36
9148xx-37 9148xx-46 9148xx-47 9148xx-53 9148xx-58
9148xx-60
9150xx-04 9150xx-08
9248xx-39
9250xx-08
Winbond
W83193R-01 W83193R-02 W83193R-04
W83194R-17 W83194R-37 W83194R-39 W83194R-39A
W83196S-14
PhaseLink
PLL52C63-01
PLL52C65-02
PLL52C66-23 PLL52C66-28 PLL52C66-29
PLL52C66-31 PLL52C66-38 PLL52C66-39
PLL52C68-02 PLL52C68-04
IMI
SC643 SC654
SG543
SG745 SG748 SG750
C-Media
CMA8864-04 CMA8864-17 CMA8864-26 CMA8864-36 CMA8864-37
CMA8864-39
Unsupported PLL-ICs
The following PLL-ICs cannot have their settings altered by software. (This is the main thing people ask me about)
IC-Works
W130x W137x W146x W155x
W48C100-01x W48C101-01x W48C111-12x W48C111-16x W48C111-17x
ICS
9147xx-03 9147xx-09 9148xx-03 9148xx-10 9148xx-20
9148xx-25 9148xx-49 9248xx-20 9248xx-50 9248xx-55
9248x-61
PhaseLink
PLL52C59-14 PLL52C61-23 PLL52C61-01 PLL52C62-01 PLL52C64-06
PLL52C66-05 PLL52C68-06
IMI
SC401 SC405 SC462 SC464 SC465
SC468 SC471 SC480 SC481 SC484
SC485 SC492 SC493 SC497 SC498
SC499
SC601 SC602 SC603 SC604 SC605
SC606 SC607 SC608 SC609 SC610
SC611 SC612 SC613 SC615 SC616
SC617 SC618 SC619 SC621 SC626
SC627 SC628 SC629 SC644 SC651
SC652 SC653 SC657 SC660 SC661
SC662 SC663 SC665 SC672 SC673
SC674 SC675 SC676 SC677 SC678
SC679 SC680 SC683 SC691 SC692
SC693 SC695 SC698 SC699
SG500 SG501 SG502 SG504 SG508
SG509 SG511 SG529 SG533 SG536
SG551 SG552 SG553 SG556 SG557
SG559 SG570 SG571 SG572 SG577
SG579 SG742
XG571 XG552
C-Media
CMA8860-xx CMA8863-03 CMA8865-27
Cypress
CY2250 CY2252 CY2254 CY2255 CY2256
CY2257 CY2260 CY2264 CY2265 CY2267
CY2274 CY2278 CY2280 CY2281 CY2282
CY2285
Winbond W83977TF-xx ... These are not Clock Generators(PLL-ICs).
They are Super I/O Controller. Do not mistake them for PLL-ICs !!
History
Old History ... A reference to the Japanese documentation
Ver.1.5 '98/11/19[THU] Disclosure TaskTray mode.
Supported P2B-F(New) after BIOS 1009.
Ver.1.6-B5 '99/04/25[SUN] Added. many PLL-IC.
Added. Version check of DLL/VxD/SYS files.
Ver.1.6-B7 '99/05/17[MON] Supported. i810 Chip-set.
Supported. C-Media PLL-IC.
Ver.1.6-B9 '99/06/19[SAT] Added. SMBus Mutex-Object Control I/F.
SMBus Mutex-Object Support software
MAX1617 Monitor software 1617mon Mr. t_knz
LM75/LM78 STATUS for Windows WLMSTAT Mr. PENTIUM 666MHz
Ver.1.7 '99/07/20[TUE] Added. Window of "M/B menu creator".
Added. Window of "PLL-IC data creator".
Changed. "Option control".
Added. "New Access control" of PLL-IC.
Added. SmartBus Control (Unsupported).
Ver.1.7a '99/07/25[SUN] Fixed. "PLL-IC data creator".
Ver.1.7final '99/12/13[MON] v1.7 final version. |
|
楼主: 极速捕风
狗仔卡
离线
